Façade cassettespro
Drilled diamond cassette
Pyramidal relief whose four facets carry round holes in a gradient: the diameter follows the distance to the apex. Pitch, diameters, pattern and gradient direction are adjustable.
Open in the studio
ACM 3D Studio
- Developed
- 714.1 × 519.6 mm
- Material
- ACM 4 mm
- Folds
- 11
- Mark
- pyramid-perforated
Fabrication data
Drilled diamond cassette — at 600 × 400 mm in 4 mm ACM, this family unfolds into a 714.1 × 519.6 mm flat pattern with 11 folds, all grooved from the back: no pass on the coated face. A 1,500 × 3,200 mm sheet holds 12 of them, for 14.6 % waste.
- Material per panel
- 0.342 m²
- Folds
- 11
- Total groove length
- 4,742 mm
- Cutting length
- 3,535 mm
- Corner slits
- 1
- Corner reliefs
- 3
- Drill holes
- 422
V-grooves (apex angle)
- 90°1,664 mm
- 78.7°1,195 mm
- 13.6°1,088 mm
- 82.4°795 mm
Panels per sheet
- 1,220 × 2,440 mm6(31.1 % waste)
- 1,500 × 3,200 mm12(14.6 % waste)
DXF layers
- CONTOUR3,535 mm
- RAINURE_902,459 mm
- RAINURE_1001,195 mm
- RAINURE_1601,088 mm
- PERCAGE× 422
The names and colours your CAM software will show. RAINURE_AVANT: fold concave on the visible face, sheet flipped for that pass.
Computed by the engine at the default parameters, on 4 mm ACM and the reference router. Your own machine and material profiles change these values in the studio.
Parameters
| Parameters | Range | Default |
|---|---|---|
| Width | 200 – 3,000 mm | 600 mm |
| Height | 200 – 3,000 mm | 400 mm |
| Relief height | 5 – 150 mm | 40 mm |
| Apex position X | 10 – 90 % | 50 % |
| Apex position Y | 10 – 90 % | 50 % |
| Return depth | 0 – 200 mm | 40 mm |
| Fixing tabs | — | ✓ |
| Tab width | 10 – 60 mm | 20 mm |
| Circular perforation | — | ✓ |
| Perforated facets | Main facet / All | All |
| Pattern | Grid / Staggered | Staggered |
| Pitch | 8 – 120 mm | 20 mm |
| Largest diameter | 2 – 60 mm | 11 mm |
| Smallest diameter | 1 – 60 mm | 3 mm |
| Diameter gradient | None / Linear / Radial / By available space | Radial |
| Gradient direction | 0 – 360 ° | 45 ° |
| Invert (large holes at the edge) | — | ✓ |
| Solid margin | 5 – 100 mm | 20 mm |
PresetsLarge holes at the edgeLarge holes near the apex
Manufacturing constraints
- The return must exceed the groove width plus half the bend deduction, or the groove eats into the return.
- Facet-to-facet folds are grooved with the smallest cutter of the profile, V left open: the angle is held by the geometry. The angle between two facets must not exceed that cutter’s apex angle.
- Vertical returns, all tabs flat in the −D plane (rail mounting). The facet-to-return fold is 90° ± slope: below 90°, the 90° cutter is left open and the return is held by the riveted tab; above 90° (facet descending towards the edge), a wider cutter (60° nominal = 120° apex) or the machine profile’s overfold tolerance is needed.
- Every raised vertex requires a V-slit to the edge (a flat sheet has 360°, the relief less). Near the vertex the slit is narrower than the contour tool: it is cut along its axis and the tool bites each facet by up to Ø/2.
- Tabs are shortened at every corner and every kink of the edge so they never collide behind the panel: by (return + 2 mm), and more on a sharp corner, where the bisector must be cleared (tab width ÷ tan(angle/2)). An edge too short gets no tab.
- Holes at the given pitch: the largest hole is reduced to keep at least the contour tool diameter of material between neighbours; every hole fits inside the facet minus the margin. Holes smaller than the contour tool are drilled (PERCAGE layer).
- The edge margin must cover half the bend deduction (the fold axis moves into the facet) plus half the widest groove, or a hole bites into the V-groove.